October Quick Start Guide for UDC Universal Digital Controller. For detailed instructions see UDC Controller Product Manual UDC Application Note. UDC AS AN AUTO/MANUAL STATION. SEVERAL CUSTOMERS HAVE LEARNED THAT THE UDC IS AN EXCELLENT. View and Download Honeywell UDC product manual online. Universal Digital Controller. UDC Controller pdf manual download.
|Published (Last):||13 January 2008|
|PDF File Size:||7.27 Mb|
|ePub File Size:||13.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
The controller is in Monitor Mode if the Shed timer is disabled.
Write this number down. Integer data udc200 represented in sixteen bits and is transferred high byte first. Radiamatic input signal that is the ratio of the actual energy emitted from the target to the energy which would be emitted if the target were a perfect radiator. The soak deviation value is the number in engineering units, above or below the setpoint, outside of which the timer halts. Page – Position Proportional and Three Position If it works, the key name will appear in the lower display.
Installation 2 Installation 2. Don’t show me this message again. Honsywell Position Proportional calibration.
Calibration and Keyboard Lockout groups are not available. Table Mounting Procedure For honewell installation, install four screws with washers into the four recessed areas in the corners of the front bezel Figure Customer should size fuses accordingly. Page 79 Radiamatic input signal that is the ratio of the actual energy emitted from the target to the energy which would be emitted if the target were a perfect radiator. Comments to this Manuals Your Name.
The instrument configuration will now be the same as it was when the instrument left the factory and all user- entered configurations since that time have been overwritten. Restoring Factory Configuration The instrument configuration will now be the same as it was when the instrument left the factory and all user- entered configurations since that time have been overwritten.
Controller Failure Symptoms In addition to the error message janual, there are failure symptoms that can be identified by noting how the controller displays and indicators are reacting. Change Auxiliary Output board. Input Calibration This section describes the field calibration procedures for Input 1 and Input 2.
Algorithm Set Up Group hysteresis of the on and off states of each output. SS plus a clockwise rotating clock face. Auxiliary Output and Digital Input 2 are mutually exclusive.
HONEYWELL UDC PRODUCT MANUAL Pdf Download.
Scroll through Function Function Function returns to: Output Set Up Group to ohms feedback slidewire. Both analog inputs are sampled six times per second every ms. This instrument is an ideal controller for regulating temperature and other process variables in numerous heating and cooling applications, as well as in metal working, food, pharmaceuticals, semiconductor, testing and environmental work.
Outputs 1 and 2 Terminals. Some are Read Only and are indicated as such and cannot be changed.
Read the pre-installation information, check the model number interpretation Subsection 2. If there is a malfunction, a diagnostic message will be displayed blinking in the lower udc320. Analog Inputs and Outputs: Electrical Noise Precautions Electrical noise is composed of unabated electrical signals which produce undesirable effects in measurements and control circuits.
Manual to Automatic is bumpless. Table Integer Parameter Type Integer data is represented in sixteen bits and is transferred high byte first.
Honeywell UDC3200 Product Manual
The ramp is placed in hold at the beginning. Page of Go. Entering a 0 will imply an immediate step change in Setpoint i. DP value by “90” to normalize the equation.
For higher temperatures, the RH specification is derated to maintain constant moisture content. Mounting Notes Before mounting the controller, refer to the nameplate on the outside of the case and make a note of the model number. Read Configuration Examples Where: The tuning parameters calculated by this selection are aimed at reducing PV overshoot of the SP setting. Digital Inputs and Digital Outputs: If you select PD with Manual Reset you can also configure the following variations: Electromechanical relays are rated at 5 Amps Vac or Vac or 30 Vdc Customer should size fuses accordingly.
Program Contents Table lists all the program contents and a description of each. Page – Table Troubleshooting Time Proportio Page 65 Three Position Step Control applications. Otherwise, the input at the instrument terminals will always be 0 mA i. Changing The Local Setpoints Fast Tune will tune the process in such a way that the temp is reached faster, a slight overshoot will be allowed. LAN rather than using a Hub. Permanently connected, panel-mounted Industrial Control Equipment with protective earthing grounding EN