I/O Wiring. PowerFlex 4M Quick Start Guide. Display. Parameter Group. First Shown when drive powered up. Display Group. (View Only). Basic Program Group. Allen-Bradley, Rockwell Automation, and PowerFlex are registered trademarks of PowerFlex 4M Adjustable Frequency Drive FRN – User Manual. View and Download ALLEN BRADLEY PowerFlex 4M user manual online. FRN 1 Series, FRN 2 Series, Adjustable Frequency AC Drive. PowerFlex 4M.
|Published (Last):||15 November 2008|
|PDF File Size:||17.18 Mb|
|ePub File Size:||13.42 Mb|
|Price:||Free* [*Free Regsitration Required]|
Read the General Precautions section before al,en. View the content here: Chapters Table Of Contents This filter is suitable for use with a cable length up to meters feet for Class A and 25 meters 82 feet for Class B environments. Our Integrated Architecture Solutions provide the foundation to drive plantwide optimization efficiently and effectively, enabling you to respond competitively to the economy and changes in consumer demand.
ALLEN BRADLEY PowerFlex 4M User Manual
Additional Information Our industry expertise helps deliver complete Drive System Solutions that maximize production and minimize risk. To simplify drive setup, the most commonly programmed parameters are organized in a single Basic Program Group. Page 32 Keep wire length as short as possible between the enclosure entry point and the EMI filter. Motor Ground Mahual motor ground must be connected to one of the ground terminals on the drive.
Tighten screw after nanual removal. Supplemental Drive Information Notes: Page 33 Installations on a public low voltage power network may require additional external harmonic mitigation. Application specific thermal considerations may require a larger enclosure.
Caution should be used when enabling this feature, since the drive will attempt to issue its own start command based on user selected programming. Appendix B Refer to for accessory ordering information.
Page 74 Type 2 that indicate possible drive component malfunction are not resettable. Press Enter or Sel to enter the group menu again. Connect with the best — locally and globally. Failure has been detected in the 1.
Page 39 [Output Frequency] is displayed. Communications Group Stops drive via coast to stop. Page Figure B.
Chapter Troubleshooting Chapter 4 provides information to guide you in troubleshooting the PowerFlex 4M drive. Page 76 Failure has been detected in the 1.
PowerFlex 4M AC Drives
Information on reading register address clarified. Replace drive if fault cannot be cleared. Don’t show me this message again.
Sets the highest frequency the drive will output. Procurement Specifications — Visit our online resource to find the procurement specifications for this product. See Appendix B for details. Stop input also clears active fault. Parameters marked 32 bit will have two parameter numbers when using RS communications and programming software.
ALLEN BRADLEY POWERFLEX 4M USER MANUAL Pdf Download.
Powerflexx will not power up without a jumper or inductor connected. By pressing ‘print’ button you will print only current page. Guidelines on standard RS wiring practices added.
Save a change to a parameter value. User Manuals Wiring Diagrams. Certifications apply when product is marked. Looking for Additional Information? Main Control Board software version. Enables the output to be controlled by bit 6 of the logic command word.
ProposalWorks — Build complete quotes and proposals. Page 90 This filter is suitable for use with a cable length up to meters feet for Class A and 25 meters 82 feet for Class B environments. Page 40 Start Up Notes: Internal brake IGBT included with power ratings 5.
22F-A4P2N – – Allen Bradley – PowerFlex 4M kW (1 Hp) AC Drive
Power must be applied to the drive to perform the following start-up procedures. Page 4 Description for option 21 of parameter t [Relay Out Sel] corrected.
Pull the cover out aolen up to release. Page 30 Preset Frequency. Braldey achha lagta hai electrical. Description for bits 6, 7, and 15 of register address updated. Page 58 Do not create a program that frequently uses configurable outputs to write parameter data to NVS unless C [Comm Write Mode] is set to option 1. Don’t have an account?